CatchmentNamData Class

Protected constructor

Additional parameters for the NAM catchment. These parameters are not used for the calculation, but can be used to calculate parameters for the catchment

Additional constant flow added to the total runoff Unit: [m3/s] Default: 0

Total area of catchment Type: Catchment area Unit: [m2] Default: 1e8 (100 km2)

Full area of catchment Type: Catchment area Unit: [km2] Default: 100

Autocalibration

Variable holding the base temperature defining if the precipitation is snow or rain (T0). Type: temperature Unit: [celcius] Default: 0.0

Variable expressing at which ground water depth the capilar flux is 1 mm/day when the lower zone is completely dry (GWLfl1). Type: Ground water depth Unit: [meter] Default: 0.0

Get and set the list of coordinates of the catchment

Catchment name.

The name is not unique, there may be several catchment models for one catchment, however all catchments with the same name should/must share the same catchment geometry.

Get and set the central point of the catchment

A Component Source provides info on concentration of various components.

Variable holding the constant degree day coefficient (Csnow). Type: Melting Coefficient Unit: [mm/Celcius/day] Default: 2.0

The ground water depth at which the base flow equals zero (GWLBF0). Constant value, used when UseSeasonalGwDepthForZeroBaseFlow is false

Type: Ground water depth. Unit: [meter]. Default: 10.

Variables holding the seasonal crop coefficientsas read from the file Type: Dimensionless factor Unit: [] Default: 1

Used only when UseCropCoeffsAndLosses is set.

Current time of catchment

Effective area. The effective area is the area that collects water. Can be smaller than total area, eg for Linear Reservoir or when LIDs are present.

End time of catchment data - the latest time for which the catchment can return data

Variable holding the chainage of the external river delivering irrigation water.

Variable holding the name of the external river delivering irrigation water Type: River Name Default: Blank

This variable holds the ratio between ground water reservoir and the catchment area (Carea). It is multiplied with the baseflow after updating the groundwater depth with infiltration. Type: Dimensionless factor Unit: [] Default: 1

This flag tells if the catchment should be divided into elevation zones used when ice modelling is included. Default: false

This flag determines if a radiation coefficient should be use in the calculation. Default: false

This flag decides if a rainfall degree day coefficient should be used. Default: false.

This flag tells if snow is included in the calculation Default: false

Variable holding the infiltartion rate at field capacity (K0inf). Type: Infiltration Unit: [mm/h] Default: 1

Initial conditions for NAM state variables.

Variables holding the seasonal losses in percent due to evaporation as read from the file Type: Dimensionless factor Unit: [%] Default: 0

Used only when UseCropCoeffsAndLosses is set.

Variables holding the seasonal losses in percent to groundwater Type: Dimensionless factor Unit: [%] Default: 0

Used only when UseCropCoeffsAndLosses is set.

Variables holding the seasonal losses in percent to over land flow as read from the file Type: Dimensionless factor Unit: [%] Default: 0

Used only when UseCropCoeffsAndLosses is set.

Variable holding the fraction of the infiltration to the ground water that enters the lower ground water storage (CQlow). If set to zero, the lower ground water storage is not enabled. Type: Lower baseflow Unit: [percent] Default: 0.0

Holds the maximum groundwater depth corresponding to a zero base flow. Used when UseSeasonalGwDepthForZeroBaseFlow. Type: Ground water depth Unit: [meter] Default: 10

Maximum runoff flow

Holds the minimum groundwater depth at which the groundwater is transfered to the upper storage (GWLmin). Type: Ground water depth Unit: [meter] Default: 0

Holds the minimum groundwater depth corresponding to a zero base flow. Used when UseSeasonalGwDepthForZeroBaseFlow. Type: Ground water depth Unit: [meter] Default: 0

Minimum runoff flow

Minimum time the catchment should be able to provide values. The catchment will cache or recalculate values from MinTime to EndTime. MinTime must be updated ("dragged behind" time of calculation) from the caller to allow the catchment to discard cached values.

Catchment model ID. Unique id.

Variable holding the number of inidividual snow zones. When set, all snow zone parameter arrays are recreated and reset to default values. Default: 1

Observed data. Used for creating calibration plots and for auto-calibration reference data.

Coefficient for overland flow runoff (CQOF). It expresses the part of the net rainfall that run off as over land flow. Type: Dimensionless Unit: [] Default: 0.5

Variable telling the percentage of irrigation source that originates from external river. Type: Dimensionless Factor Unit: [] Default: 0

Variable telling the percentage of irrigation source that originates from local ground water. Type: Dimensionless Factor Unit: [] Default: 50

Variable telling the percentage of irrigation source that originates from local river. Type: Dimensionless Factor Unit: [] Default: 50

Number of person equivalent in the catchment, used with catchment discharge source boundary

Variable holding the radiation coefficient (Crad); Type: Dimensionless factor Default: 0.0;

Variable holding the rainfall degree day coefficient (Crain). Type: Rain Melting Coefficient per degree per time Unit: [/celcius/day] Default: 0.0

Maximum storage in the root/lower zone (L_max) Type: Storage depth Unit: [mm] Default: 100.00

Get the Diagnostics instance for a Catchment. Used during runtime.

This array holds the seasonal variation of the degree day coefficient (Csnow). Type: melting Coefficient Unit: [mm/celcius/day] Default: 1, 1.5, 2, 3, 4, 4.5, 4.5, 4, 3, 2, 1.5, 1

This flag determines if the seasonal variation of the degree day coefficient is specified in a time series. Default: false

Holds the relative seasonal depth used to calculated the groundwater depth corresponding to a zero base flow. Used when UseSeasonalGwDepthForZeroBaseFlow. Type: Dimensionless factor Unit: [] Default: 1

Holds the specific yield for the groundwater reservoir (Sy). Type: Dimensionless factor Unit: [] Default: 0.1

Start time of catchment data - the earliest time for which the catchment can return data

List of Lids

Maximum surface/upper storage (Umax) Type: Storage Depth Unit: [mm] Default: 10.00

Root zone treshold for recharging groundwater (TG) Type: Dimensionless factor Unit: [] Default: 0

Root zone treshold for inter flow (TIF) Type: Dimensionless factor Unit: [] Default: 0

Root zone treshold for overland flow (TOF) Type: Dimensionless factor Unit: [] Default: 0

Time constant for the routing of base flow (CKBF) Type: Flow routing time constant Unit: [hour] Default: 2000

Time constant for the first linear reservoir routing (CK1), for overland and interflow. Type: Flow routing time constant Unit: [hour] Default: 10

Time constant for the first linear reservoir routing of inter flow (CKIF) Type: Flow routing time constant Unit: [hour] Default: 1000

Variable holding the time constant for routing ground water in the lower ground water reservoir (CKlow). Type: Flow routing time constant Unit: [hour] Default: 10000

Time constant for the second linear reservoir routing (CK2), for overland flow. Type: Flow routing time constant Unit: [hour] Default: 10

Time of minimum runoff flow

Time of maximum runoff flow

Time step used by the rainfall runoff model

Total volume of additional inflow

Total infiltration into this catchment (integrated over time)

Total rainfall on this catchment (integrated over time)

Total runoff from this catchment (integrated over time)

Set the TSBuffer to use in this catchment

Flag telling if abstraction of ground water should be included. Default: false

Flag telling if seasonal crop coefficients and losses should be specified. Default: false

Flag telling if the evaporation has to be reduced by the snow cover. If False (default MIKE 11) the evaporation will be reduced by the snow cover, if True (default MIKE URBAN), full evaporation occurs even on the ground where there is snow Type: bool Default: False

Flag telling if initial conditions is taken from a hotstart file Default: false

Flag telling if the irrigation module should be applied. Type: bool Default: False

This flag determines if a seasonal variation of the degree day coefficient should be used. Default: false

Flag telling if a seasonal variation of the ground water depth corresponding to zero base flow should be used. Default: false

Return dictionary of runoff as a function of year

Variables holding the areas of the different zones. Type: Catchment area Unit: [km2] Default: 0, not used in case of only one snow zone, the total catchment area is used instead.

Variables holding the dry temperature correction for the different zones. Type: Temperature correction Unit: [celcius] Default: 0

Variables holding the elevations for the different zones. These values are not used during the calculation, but used elsewhere to calculate parameters in different snow zones. Type: Elevation Unit: [meter] Default: 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000

Variables holding the maximum storage at the different zones Type: Storage depth Unit: [mm] Default: 10000, if only one snow zone: 0.

Variables holding the maximum amount of water contained in the snow. Type: Max Water Unit: [%] Default: 0

Variables holding the minimum storage for full coverage for each zone Type: Storage depth Unit: [mm] Default: 100, if only one snow zone: 0.

Variables holding the precipitation correction for the different zones. Type: Precipitation correction Unit: [%] Default: 0

Variables holding the wet temperature correction for the different zones. Type: Temperature correction Unit: [celcius] Default: 0

Apply a boundary to this catchment

Apply a boundary to this catchment

Apply boundary to LID's in catchment

Apply boundary to LID's in catchment

Return true if boundaries of the specified type are additive; the contributions of two discharge boundaries add up, while two temperature boundaries do not.

Calculate statistics.

Called at end of each time step, by PerformTimeStep

Calculate and update yearly statistics, YearlyRunoff.

Called at end of each time step, in PerformTimeStep

Determines whether the specified object is equal to the current object.

Destructor

Serves as a hash function for a particular type.

Get the type of boundary required by this catchment

Gets the Type of the current instance.

This procedure initializes all the state variables declared for the catchment.

Initialize Rainfall Runoff model. Sets up static data.

Creates a shallow copy of the current Object.

This procedure forwards the calculation with one time step.

Prepare Rainfall Runoff model. Sets up dynamic data so that the model is ready for first time step.

Prepare boundary source.

Prepare state for new simulation.

Remove boundaries applied in previous runs

This procedure is the one actually calculating the new time step.

List of data types that is accepted and can be used in SetValue

List of data types that is offered and can be used in GetValue

Return the time of next update. Used for PostTimeStepEvent event in Catchments. If a catchment uses variable timesteps, then this function must be overridden!!

Get value setter for the specified data quantity

Get value setter for the specified data quantity

Get value setter for the specified data quantity

Get value setter for the specified data type

Returns a string that represents the current object.

This routine stores the calculated variables in variables ready for export. The values in these state variable corresponds to the values written to the result file. All discharge variables are subject to a unit conversion. During the calculation discharges are calculated using the unit mm/hour and must therefor be converted into m3/s.

Trigger the PostTimeStepEvent, called at end of a time step.

The type of catchment: NAM, Urban A etc

Update internal state of catchment to time Time()

Validate that the catchment is set up correctly

Validate all LIDs in catchment

Volume of water stored in catchment after previous TakeTimeStep()

Volume of water stored in catchment after previous TakeTimeStep()

Event that is triggered every time the catchment has finished a new time step

Additional constant flow added to the total runoff Unit: [m3/s] Default: 0

Additional constant flow at start of time step

Total area of catchment. Type: Catchment area. Unit: [m2]. Default: 1e8 (100 km2).

Evaporation boundary source

Rainfall boundary source

Temperature boundary source

Variables holding the seasonal crop coefficients Type: Dimensionless factor Unit: [] Default: 1

Time step used in the simulation, it may change. It is set in Prepare to _timeStep, and can be updated by individual catchment models when required, i.e. it may differ from _timeStep.

Protected end time of catchment data - the latest time for which the catchment can return data

This flag tells if snow is included in the calculation Default: false

Maximum flow

Minimum flow

Proteced MinTime

List of datatypes offered in GetValue

Diagnostics instance for a Catchment. Used during runtime.

Protected start time of catchment data - the earliest time for which the catchment can return data

State variables in catchment

List of Lids

Variable holding information on the latest calulated time

Last time the state of this catchment was updated (Update(DateTime) was called)

Time of maximum flow

Time of minimum flow

Variable holding information on the latest calulated time

Time step used in the simulation, or initial time step if the time step can change.

Time step used in the NAM rainfall runoff model Unit: [hours]

Fraction of time between prev time and current time for the last call to Update(DateTime). This should be updated everytime _timeOfLastUpdate is updated.

Total volume of additional inflow

Total volume of loss

Total volume of rain

Total volume of runoff

TSBuffer to use when accessing time series objects Set in Catchments.Add(). If not set, then the inheritors must create a TSBuffer before using it.

Flag telling if initial conditions is taken from a hotstart file Default: false

Dictionary of runoff as a function of year

Sets up monthly abstraction for nam, assuming the abstraction values are in mm/month.